4 PIN IR Infrared Flame Detection Sensor Module

@ TECH HALLROAD

4 PIN IR Infrared Flame Detection Sensor Module or Fire Sensor module is a small size electronics device that can detect a fire source or any other bright light sources. This sensor basically detects IR (Infrared) light wavelength between 760 nm – 1100 nm that is emitted from the fire flame or light source.

 150.00

In stock

Categories: ,

4 PIN IR Infrared Flame Detection Sensor Module or Fire Sensor module is a small size electronics device that can detect a fire source or any other bright light sources. This sensor basically detects IR (Infrared) light wavelength between 760 nm – 1100 nm that is emitted from the fire flame or light source.

The 4 PIN IR Infrared Flame Detection Sensor Module comes with a YG1006 Phototransistor sensor which is a high speed and high sensitivity.  4 PIN IR Infrared Flame Detection Sensor Module can easily use with Arduino and other microcontroller boards.

A 4 PIN IR Infrared Flame Detection Sensor Module that consists of a flame sensor (IR receiver), resistor, capacitor, potentiometer, and comparator LM393 in an integrated circuit. It can detect infrared light with a wavelength ranging from 700nm to 1000nm.

The far-infrared flame probe converts the light detected in the form of infrared light into current changes. Sensitivity is adjusted through the onboard variable resistor with a detection angle of 60 degrees.

Working voltage is between 3.3v and 5.2v DC, with a digital output to indicate the presence of a signal. Sensing is conditioned by an LM393 comparator.

4 PIN IR Infrared Flame Detection Sensor Module suitable for use with a Arduino, Raspberry Pi and other microcontrollers.
The analog signal pin provides an output based on the level of radiation available to the sensor. The digital signal pin outputs HIGH when the level goes above the trigger level and low when below it.

The trigger level can be adjusted via the onboard potentiometer. The 4 PIN IR Infrared Flame Detection Sensor Module will output HIGH values when detecting light and LOW values when no light detected. The module features an LED which illuminates when the sensor is detecting above the trigger level.

Features: –

  • The flame sensor is most sensitive to flame and it will also respond to ordinary light, generally used in fire alarm and other purposes.
  • A small panel output interface can directly connect with the microcontroller IO port.
  • The sensor should be kept a certain distance from the flame, so as not to damage the sensor because of high temperature.
  • the test distance for the lighter flame should be 80cm,the larger the flame, the larger the test distance.
  • Small plates analog output mode and the AD conversion process can help get higher accuracy.

4 PIN IR Infrared Flame Detection Sensor Module Specifications: –

  • Can detect the flame or the wavelength at 760 nm to 1100 nm range of the light source, the test flame lighters distance of 80cm, the larger the flame, the greater the distance test.
  • The detection angle of 60 degrees, the flame spectrum particularly sensitive.
  • Sensitivity adjustable. (shown in blue digital potentiometer adjustment)
  • The comparator output signal clean waveform is good, driving ability, than 15mA.
  • With a precision potentiometer adjustable sensitivity adjustment.
  • Operating Voltage 3.3V-5V.
  • The output in the form: DO digital switching outputs (0 and 1) and AO analog voltage output.
  • A fixed bolt holes for easy installation.
  • Small plates PCB size: 3.2cmx1.4cm.
  • Using a wide voltage LM393 comparator.

Pin Description: –

  • VCC: VCC3.3-5V.
  • GND: GND.
  • DO: TTL switch signal output.
  • AO: Analog Output.
Applications: –
  • The flame flame sensor most sensitive to ordinary light is also a reaction, generally use as fire alarm and other purposes.
  • A small panel output interface can directly connect with the microcontroller IO port.
  • The sensor and the flame to maintain a certain distance, so as not to damage the sensor temperature of the test flame lighters distance 80cm, the larger the flame, the greater the distance test.
  • Small plates analog output mode and the AD conversion process, you can get higher accuracy.
Package: –

1 x 4 PIN IR Infrared Flame Detection Sensor Module

Related Products at majju.pk

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “4 PIN IR Infrared Flame Detection Sensor Module”

Vendor Information

  • Store Name: TECH HALLROAD
  • Vendor: TECH HALLROAD
  • Address:
  • 5.00 5.00 rating from 2 reviews
4 PIN IR Infrared Flame Detection Sensor Module
4 PIN IR Infrared Flame Detection Sensor Module

 150.00

Majju PK
Logo
Reset Password
Shopping cart