DHT11 Temperature Humidity Sensor Module for Arduino

Sold by
sherjaan
@ sherjaan

Digital temperature and humidity sensor DHT11 is a low-cost, easy-to-use sensor that is commonly used in a variety of applications. DHT11 sensor has a single data pin that is used to communicate with the host microcontroller.

 250.00

In stock

Category: Tag:

The DHT11 is a digital temperature and humidity sensor. DHT11 sensor has a built-in NTC thermistor to measure humidity and a capacitive humidity sensor to measure temperature.

Digital temperature and humidity sensor DHT11 is a low-cost, easy-to-use sensor that is commonly used in a variety of applications. DHT11 sensor has a single data pin that is used to communicate with the host microcontroller. The sensor uses a one-wire protocol, which makes it easy to interface with the microcontroller. DHT11 sensor can be read by the microcontroller using a simple polling method.

The DHT11 sensor has a temperature range of 0°C to 50°C and a humidity range of 20% to 90%. The sensor has an accuracy of ±2°C and ±5%RH. The DHT11 sensor is a reliable and accurate sensor that is a good choice for many applications.

It is important to note that the DHT11 not designed to be powered by a higher voltage than 5.5V, as this could damage the sensor. The DHT11 is a digital temperature and humidity sensor that can  power by a voltage range of 3.3V to 5.5V. The recommended input voltage for the DHT11 is 5V.

The DHT11 has a maximum current draw of 2.5mA, which is relatively low. This means that the DHT11 can power by a small battery or a USB power supply. The DHT11 has a data pin that used to communicate with the host microcontroller. The data pin pulled up to 5V by a 10K resistor. This means that the microcontroller can read the data from the DHT11 without having to provide any additional power to the sensor.

Features : –

The DHT11 is a digital temperature and humidity sensor that uses a capacitive humidity sensor and an NTC thermistor to measure the surrounding air. The capacitive humidity sensor consists of two electrodes with a moisture holding substrate as a dielectric between them. As the humidity levels change, the capacitance of the sensor changes. The NTC thermistor is a resistor whose resistance decreases as the temperature increases.

Here are some of the advantages of using the DHT11 sensor:

  • Low cost
  • Easy to use
  • Single data pin
  • One-wire protocol
  • Wide temperature and humidity range
  • Good accuracy

DHT11 Temperature Humidity Sensor Specifications : –

The DHT-11 sensor has a single data pin that used to communicate with the host microcontroller. The sensor uses a one-wire protocol, which makes it easy to interface with the microcontroller. The DHT11 sensor can be read by the microcontroller using a simple polling method.

The DHT-11 sensor has a temperature range of 0°C to 50°C and a humidity range of 20% to 90%. The sensor has an accuracy of ±2°C and ±5%RH.

Here are some of the specifications of the DHT-11 digital temperature and humidity sensor:

  • Operating voltage: 3.3V to 5.5V
  • Current draw: 2.5mA
  • Data pin: Single data pin
  • Communication protocol: One-wire protocol
  • Temperature range: 0°C to 50°C
  • Humidity range: 20% to 90%
  • Accuracy: ±2°C and ±5%RH
  • Response time: 20 milliseconds
  • Dimensions: 15.5mm x 12mm x 5.5mm

DHT11 Temperature Humidity Sensor Pin Descriptions : –

The DHT-11 digital temperature and humidity sensor has 4 pins:

  • VCC: The VCC pin is the power supply pin for the sensor. It should connect to a voltage source of 3.3V to 5.5V.
  • DATA: The DATA pin is the data pin for the sensor. It used to communicate with the sensor using the one-wire protocol.
  • GND: The GND pin is the ground pin for the sensor. It should connect to a common ground.
  • NC: The NC pin is not connected to anything. It typically left unconnected.

The DHT-11 sensor is a reliable and accurate sensor that is a good choice for many applications. The low cost and easy-to-use interface make the DHT-11 a popular choice for hobbyists and professionals alike.

DHT11 Temperature Humidity Sensor Applications : –

DHT-11 digital temperature and humidity sensor is a versatile sensor that can use in a variety of applications. Some of the most common applications for the DHT-11 sensor include:

  • Weather stations
  • Home automation
  • Agriculture
  • Industrial applications
  • Scientific research

Overall, the DHT-11 is a good choice for applications where low cost and ease of use are more important than accuracy. 

Package : –

1 x DHT-11 Temperature Humidity Sensor

More Products at majju.pk

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “DHT11 Temperature Humidity Sensor Module for Arduino”

Vendor Information

  • Store Name: sherjaan
  • Vendor: sherjaan
  • Address:
  • 5.00 5.00 rating from 6 reviews
DHT11 Temperature Humidity Sensor Module for Arduino
DHT11 Temperature Humidity Sensor Module for Arduino

 250.00

Majju PK
Logo
Reset Password
Shopping cart