Name: 2.8 Inch SPI TFT LCD ILI9341 5V 240X320 Module
SKU: 15472
Price: 2000.00 PKR
Availability: OutOfStock

This 2.8 Inch SPI TFT LCD ILI9341 5V 240X320 Module is a full color display with a resolution of 240 x 320 pixels. It uses the ILI9341 controller with SPI interface. It also includes a resistive touchscreen with built-in XPT2046 controller.

As a bonus, this 2.8 Inch SPI TFT LCD ILI9341 5V 240X320 Module display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen. This display has a controller built into it with RAM buffering so that almost no work is done by the microcontroller.

The display can be used in two modes: 8-bit and SPI. For 8-bit mode, you’ll need 8 digital data lines and 4 or 5 digital control lines to read and write to the display (12 lines total). SPI mode requires only 5 pins total (SPI data in, data out, clock, select, and d/c) but is slower than the 8-bit mode. In addition, 4 pins are required for the touchscreen (2 digital, 2 analogs).

This 2.8 Inch SPI TFT LCD ILI9341 5V 240X320 Module is wrapped up into an easy-to-use breakout board, with SPI connections on one end and 8-bit on the other. Both are 3-5V compliant with high-speed level shifters so you can use with any microcontroller. If you’re going with SPI mode, you can also take advantage of the onboard Micro SD card socket to display images.

The modules have an SD card socket. This socket has separate connections to the opposite end of the board.

Internally the display operates at 3.3V, so if using with a 5V microcontroller, be sure to include logic level shifters on the data lines to prevent possible damage.

Features: –

2.8″ TFT LCD with 240 x 320 resolution
65K colors with ILI9341 controller
Resistive touch screen with XPT2046 controller
SPI 4-wire interface
3.6 to 5.5V module operation
3.3V logic compatible only
It shows the color depth of 262K/65K.
Need at least 4 IOs from your MCU
The display has a wide viewing angle.
Big display with good resolution.

2.8 Inch SPI TFT LCD ILI9341 Specifications: –

Name	Parameter
Display Color	RGB 65K color
SKU	have touch screen: MSP2807
SKU	have no touch screen: MSP2806
Screen Size	2.8(inch)
Type	TFT
Driver IC	ILI9341
Resolution	320*240 (Pixel)
Module Interface	4-wire SPI interface
Active Area (AA area)	43.2×57.6(mm)
Module PCB Size	50.0×86.0(mm)
Operating Temperature	-20℃~60℃
Storage Temperature	-30℃~70℃
VCC power voltage	3.3V~5V
Logic IO port voltage	3.3V(TTL)
Power Consumption	TBD
Rough Weight(Package containing)	No touch: 34(g) / With touch: 43(g)

2.8 Inch SPI TFT LCD ILI9341 Pin Configuration: –

NO	SYMBOL	FUNCTION
1	GND	Ground
2	LED+	Anode of LED backlight.
3	LED-	Cathode of LED backlight.
4	GND	Ground
5	VDD	Power supply(TYP:2.8V).
6	RESET	System reset pin.
7	SDA	Serial data input pin and output pin(SDA) in serial bus system interface I. Serial data input pin (SDI) in serial bus system interface II. The data is inputted on the rising edge of the SCL signal. If not used, please let it open or connected to VSSD.
8	SCL	(NWR) Write enable pin I80 parallel bus system interface. (SCL) server as serial data clock in serial bus system interface when IFSEL=0. Fix it to IOVCC or VSSD level when not used.
9	CS	Chip select signal. Low: chip can be accessed; High: chip cannot be accessed. Must be connected to VSSD if not in use.
10	RS	Command / parameter or display data selection pin
11	GND	Ground
12	SDO	Serial data output pin (SDO) in serial bus system interface II. If not used, please open this pin.
13	TE	Tearing effect output. If not used, please open this pin
14	IM3	serial interface I / serial interface II
15	GND	Ground
16	NC	No connect
17	NC	No connect
18	NC	No connect
19	NC	No connect
20	GND	Ground