IIC/I2C Serial Interface Adapter I2C Interface Module for lcd

Sold by
sherjaan
@ sherjaan

IIC/I2C Serial Interface Adapter module or I2C interface module for 16×2 (1602) & 20×4 (2004) LCD displays with on-board contrast control adjustment, backlight and I2C communication interface.

 220.00

In stock

IIC/I2C Serial Interface Adapter module or I2C interface module for 16×2 (1602) & 20×4 (2004) LCD displays with on-board contrast control adjustment, backlight and I2C communication interface.

The great advantages of this I2C Serial LCD module will simplify the circuit connection, save some I/O connection pins on Arduino board, simplified firmware development with widely available Arduino library.

I2c serial lcd Daughter board that can be connected to a standard 1602 and or 2004 lcd put on view part of a greater unit that supports 4-bit mode

i2c interface module has a PCF8574 I2C chip that converts I2C serial data to parallel data for the LCD display. The I2C address is 0x3F by default, but this can be changed via 3 solder jumpers provided on the board. This allows up to 3 LCD displays to be controlled via a single I2C bus.

The power points VCC and GND can connect to the 5V and the ground terminal of the MCU/MPU, respectively. Also, connect the SDA, SCL pins of the module to the MCU/MPU I2C pins respectively to send the data.

serial i2c lcd daughter board module drives an I2C interfaced 2 line by 16 character LCD. The I2C LCD component is a wrapper around an I2C Master component and makes use of an existing I2C Master component.

iic/i2c serial interface adapter module uses in applications that require a visual or textual display. This component is also use where a character display needed but seven consecutive GPIOs on a single GPIO port are not possible.

In cases where the project already includes an I2C master, no additional GPIO pins are required.

Features: –

  • Communicate on a 2-wire I2C bus
  • The API is compatible with the current character LCD component
  • A single component may drive one or more LCDs on the same I 2C bus
  • The I2C LCD can coexist on an existing I2C bus if the PSoC is the I2C master
  • Support for the NXP PCF2119x command format

IIC/I2C Serial Interface Adapter Specifications: –

  • Compatible with Arduino Board or other controller board with I2C bus.
  • Display Type: Negative white on Blue backlight.
  • I2C Address:0x38-0x3F (0x3F default)
  • Supply voltage: 5V
  • Interface: I2C to 4bits LCD data and control lines.
  • Contrast Adjustment: built-in Potentiometer.
  • Backlight Control: Firmware or jumper wire.

IIC/I2C Serial Interface Adapter Pin Description: –

  • GND is a ground pin and should connect to the ground of Arduino.
  • VCC supplies power to the module and the LCD. Connect it to the 5V output of the Arduino or a separate power supply.
  • SDA is a Serial Data pin. This line uses for both transmit and receive. Connect to the SDA pin on the Arduino.
  • SCL is a Serial Clock pin. This is a timing signal supplied by the Bus Master device. Connect to the SCL pin on the Arduino.
IIC/I2C Serial Interface Adapter Datasheet: –

I2C_1602_LCD

Package: –

1 x IIC/I2C Serial Interface Adapter

Related Products at majju.pk

 

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “IIC/I2C Serial Interface Adapter I2C Interface Module for lcd”

Vendor Information

  • Store Name: sherjaan
  • Vendor: sherjaan
  • Address:
  • 5.00 5.00 rating from 3 reviews

You may also like…

IIC/I2C Serial Interface Adapter I2C Interface Module for lcd
IIC/I2C Serial Interface Adapter I2C Interface Module for lcd

 220.00

Majju PK
Logo
Reset Password
Shopping cart