USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor

Sold by
sherjaan
@ sherjaan

USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor is based on Thomas Fischl’s USBasp design and connect to your computer’s USB port. Not only are they quite compact (70x20mm), but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done in firmware.

 550.00

In stock

USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor is based on Thomas Fischl’s USBasp design and connect to your computer’s USB port. Not only are they quite compact (70x20mm), but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done in firmware.
Being an Open source hardware (OSHW) project, released under the GNU General Public License, you are free to download the schematic and firmware from Thomas’s website, but then you have a chicken and egg problem. In order to load the USBASP firmware onto the atmega8 on the programmer, yes you guessed it, you need an AVR programmer. Much easier to buy one fully built and programmed.

USB-AVR/51-ISP ATMEL AVR Programmer and 10 Pin Adaptor product is a USB circuit programmer manufactured for the Atmel AVR controllers. You can easily do the programming job with just one ATMega8 and a few passive components. You only need the USB Driver for programming. No special USB controller is required. The Driver links are the 7th of the datasheet file of the product located in the inventors section below. page. You can access all information about the product from the datasheet file on how to load the Driver and all information about the product.

The USB interface is achieved by using an ATmega processor and the rest is done in firmware
With 500mA over-current protection self-recovery fuse, and complete protection of expensive computer motherboard
designed for notebook computers, special two 3.6V regulators, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings.
The well-configured firmware, the speed of the unique adaptive technology, stability and obtain the best balance between speed! Supports firmware upgrade unlimited.

Features: –

  • Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
  • Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
  • 5 KB/sec maximum write speed
  • Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
  • 10 pin ISP interface (conforms to standard ISP 10-pin pinout)
  • Runs under multiple platforms. The Linux, Mac OS X, and Windows tests are done.
  • Programming speed can be up to 5kb/sec.
  • Slow SCK option to support small targets with crystal frequency 1.5 Mhz.

USB-AVR/51-ISP ATMEL AVR Programmer Specifications: –

  • USBasp is a USB in-circuit programmer for Atmel AVR controllers. It simply consists of an ATMega8 and a couple of passive components.
  • The programmer uses a firmware-only USB driver, no special USB controller needed.
  • 500mA over-current protection with self-healing fuse, to protect expensive computer motherboard!
  • designed for notebook computers, special two 3.6V regulator, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings.
  • Speed of adaptive technology
  • Programming speed is up to 5kBytes/sec
  • SCK option to support targets with low clock speed (< 1,5MHz)
  • Powered by USB
  • Standard 10-Pin ISP connector.
  • 51 Series AT89S51 AT89S52 AT89S8252

USB-AVR/51-ISP ATMEL AVR Programmer Support: –

The latest Window Drivers are fully signed, so you can use them on Windows Vista and above without any issues. The driver will work on both 32 and 64 bit platforms. On Linux And Mac OS X no kernel driver require, just use AVR dude and specify the correct port.
The programmer will work with a wide variety of Atmel AVR microcontrollers including the Atmega8a and Atmega168a. A full list is available on the specifications tab. The programmer will also work with a variety of software including.

The Microcontrollers Supported by the USB-AVR/51-ISP ATMEL AVR Programmer:

Mega Series

  • ATmega8 ATmega48 ATmega88 ATmega168 ATmega328
  • ATmega103 ATmega128 ATmega1280 ATmega1281 ATmega16
  • ATmega161 ATmega162 ATmega163 ATmega164 ATmega169
  • ATmega2560 ATmega2561 ATmega32 ATmega324 ATmega329
  • ATmega3290 ATmega64 ATmega640 ATmega644 ATmega649
  • ATmega6490 ATmega8515 ATmega8535

Attiny Series

  • Attiny12 ATtiny13 ATtiny15 ATtiny25 ATtiny26
  • Attiny45 ATtiny85 ATtiny2313

Classic Series

  • AT90S1200 AT90S2313 AT90S2333 AT90S2343 AT90S4414
  • AT90S4433 AT90S4434 AT90S8515
  • AT90S8535

CAN Series

  • AT90CAN128
  • PWM Series
  • AT90PWM2 AT90PWM3
Package: –

1 x USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor

Related Products at majju.pk

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor”

Vendor Information

  • Store Name: sherjaan
  • Vendor: sherjaan
  • Address:
  • 5.00 5.00 rating from 2 reviews
USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor
USB-AVR/51-ISP ATMEL AVR Programmer 10 Pin Adaptor

 550.00

Majju PK
Logo
Reset Password
Shopping cart