100K ohm NTC 3950 1% Thermistor For 3D Printer

This 100K ohm NTC 3950 1% thermistor is a good choice for temperature measurement in 3D printers. It has a high accuracy, wide temperature range, and long lifespan, making it a reliable and durable sensor for this application.

A 100K ohm NTC 3950 thermistor is a type of thermistor that has a resistance of 100,000 ohms at 25°C. The resistance of the thermistor decreases as the temperature increases, following an exponential relationship. NTC thermistors often use in temperature measurement applications. They are also use in self-heating devices, such as thermostats and temperature controllers.
A 100K ohm NTC 3950 thermistor works on the principle of negative temperature coefficient (NTC). This means that the resistance of the thermistor decreases as the temperature increases. 

The input voltage will depend on the circuit that the thermistor is used in. However, the thermistor’s resistance will change with temperature, so the input voltage will also change with temperature. The input voltage of a 100K ohm NTC 3950 thermistor can also be measured using a multimeter. The multimeter should be set to the resistance measurement mode and the thermistor should be connected to the multimeter’s probes. The input voltage will be the voltage reading on the multimeter.

It is important to note that the input voltage of a 100K ohm NTC 3950 thermistor will vary depending on the temperature. The input voltage will be lower when the temperature is higher and higher when the temperature is lower.

Features : –

In a 3D printer, the thermistor is used to measure the temperature of the hot end. This information is used by the printer’s firmware to control the temperature of the hot end, ensuring that the filament is melted at the correct temperature.

The 100K ohm NTC 3950 1% thermistor has a resistance of 100,000 ohms at 25°C. The resistance of the thermistor decreases as the temperature increases, following an exponential relationship. This means that the thermistor can be used to measure very small changes in temperature.

The thermistor has a temperature range of -40°C to 125°C. This makes it suitable for use in most 3D printers, which typically operate in a temperature range of 180°C to 250°C.

Here are some of the benefits of using a 100K ohm NTC 3950 1% thermistor:

• High accuracy: The 1% accuracy means that the thermistor is very precise in its measurements. This is important for applications where accuracy is critical, such as temperature control.
• Wide temperature range: The thermistor can operate in a wide temperature range, from -40°C to 125°C. This makes it suitable for a variety of applications.
• Low cost: Thermistors are relatively inexpensive, making them a cost-effective option for temperature measurement.
• Small size: Thermistors are small and lightweight, making them easy to integrate into devices.
• Long lifespan: Thermistors have a long lifespan, making them a reliable choice for long-term applications.

100K ohm NTC 3950 Specifications : –

In a 3D printer, the thermistor used to measure the temperature of the hot end. This information  used by the printer’s firmware to control the temperature of the hot end, ensuring that the filament  melted at the correct temperature.

The 100K ohm NTC 3950 1% thermistor has a resistance of 100,000 ohms at 25°C. The resistance of the thermistor decreases as the temperature increases, following an exponential relationship. This means that the thermistor can use to measure very small changes in temperature.

The thermistor has a temperature range of -40°C to 125°C. This makes it suitable for use in most 3D printers, which typically operate in a temperature range of 180°C to 250°C. here are the specifications of a 100K ohm NTC 3950 1% thermistor for 3D printers:

• Resistance: 100,000 ohms at 25°C
• B-value: 3950 K
• Temperature range: -40°C to 125°C
• Accuracy: 1%
• Long lifespan: Up to 10,000 hours
• Dimensions: 2 mm x 1 mm x 0.5 mm
• Leads: 20 AWG, 10 mm

100K ohm NTC 3950 Applications : –

The thermistor typically mount on the hot end of the 3D printer. The thermistor connected to the printer’s firmware using a simple interface. The firmware uses the thermistor’s resistance to calculate the temperature of the hot end.

The thermistor is a valuable tool for ensuring that the hot end of the printer is operating at the correct temperature. The thermistor’s accuracy and reliability help to ensure that the filament  melted at the correct temperature, which is essential for producing high-quality prints. Here are some of the applications of 100K ohm NTC 3950 thermistors:

• Temperature measurement
• Self-heating devices
• Thermistor arrays
• Temperature compensation
• Data loggers
• Industrial control
• Medical devices

Package : –

1 x 100K ohm NTC 3950

More Products at majju.pk

• 10K Ohm NTC Thermistor MF52-103 Temperature Sensor
• DHT11 Temperature Humidity Sensor Module for Arduino
• Waterproof DS18B20 Digital Temperature Sensor For Arduino