KY-028 NTC Thermistor Sensor Module for Arduino

Sold by
sherjaan
@ sherjaan

KY-028 NTC Thermistor Sensor Module is a sensor that uses NTC temperature resistance. The purpose is not to show the ambient temperature. NTC sensors produce On and Off (0/1) according to the temperature value we set.

 140.00

In stock

KY-028 NTC Thermistor Sensor Module is a sensor that uses NTC temperature resistance. The purpose is not to show the ambient temperature. NTC sensors produce On and Off (0/1) according to the temperature value we set.

One of the common uses is to ensure that fans that provide cooling of electronic circuits that produce high heat, such as power supplies, operate when the specified frequency is exceeded. The resistance value decreases as the NTC resistance on it heats up. KY-028 NTC Thermistor Sensor Module can be used in various circuits using this feature.
The temperature sensitivity is changed with the trimpot on this sensor module and the required temperature value is determined.

This KY-028 NTC Thermistor Sensor Module can measure temperatures in the range of -55°C up to +125°C. This has a decreasing resistance value at higher temperature. An NTC Thermistor is a kind of resistor with a Negative Temperature Coefficient. 

KY-028 NTC Thermistor Sensor Module has three functional components on its circuit board. One is the sensor unit at the front of the module, which physically measures the current environment and outputs it as an analog signal to the second unit, the amplifier. This amplifies the signal depending on the resistance set on the rotary potentiometer and sends it to the analog output of the module.

KY-028 NTC Thermistor Sensor Module has a digital interface, built-in 13 LED build a simple circuit, making the temperature warning lamp 13 comes with digital interfaces of the LED, the digital temperature sensor connected digital three interfaces, when the digital temperature sensor senses a key signal, LED lights, otherwise off.

Generally, the 4 wire method of thermistor measurement is the most accurate because there is effectively no current flowing in either of the measurement cable wires and therefore no added resistance due to the cable wires.

Features: –

  • Adopt the NTC thermistor sensor, sensitivity is good.
  • The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 ma.
  • With potentiometer to adjust the temperature detection threshold.
  • Working voltage: 3.3 V to 5 V.
  • Output form: digital switch output (0 and 1).
  • It has a fixed bolt hole, convenient installation.
  • Using the LM393 wide voltage comparator.

KY-028 NTC Thermistor Sensor Module Specifications: –

  • Using the NTC thermistor sensor , good sensitivity
  • The comparator output signal clean waveform is good , driving ability, than 15mA.
  • Adjust the temperature distribution bit detection threshold
  • Working voltage 3.3V-5V
  • The output format : Digital switching output (0 and 1)
  • With bolt holes for easy installation
  • Small board PCB size : 3.2cm x 1.4cm
  • Using a wide voltage LM393 comparator

Pin Description: –

  • A0 = Analog output, connects to analog input on MCU
  • GND / G  = Ground
  • +’ = Vcc (3.3 or 5V)
  • D0 = Digital output, connects to digital input on MCU
Datasheet: –

datasheetspdf.com/…402039/Joy-IT/KY-028/1

 

Package: –

1 x KY-028 NTC Thermistor Sensor Module for Arduino

Related Products at majju.pk

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “KY-028 NTC Thermistor Sensor Module for Arduino”

Vendor Information

  • Store Name: sherjaan
  • Vendor: sherjaan
  • Address:
  • 5.00 5.00 rating from 2 reviews
KY-028 NTC Thermistor Sensor Module for Arduino
KY-028 NTC Thermistor Sensor Module for Arduino

 140.00

Majju PK
Logo
Reset Password
Shopping cart