- 17%

BTS7960 IBT2 BTS7960 43A High Power Motor Driver Module

Sold by
sherjaan
@ sherjaan

BTS7960 IBT 2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.

 1,800.00  1,500.00

In stock

Flash Sale
days
0
0
hours
0
0
minutes
0
0
seconds
0
0

BTS7960 IBT 2 43A H-Bridge Motor Driver Module the drive uses an H-bridge driver module that composed by Infineon power drive chip BTS7960, with overheating and overcurrent protection.

bts7960 motor driver H-bridge driver circuit, with strong drive and braking effect, use 74HC244 chip effectively isolate the microcontroller and the motor drive High Current up to 43A

ibt 2 motor driver is a fully integrated high current H bridge module for motor drive applications.

Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, under voltage, overcurrent and short circuit.

bts7960 43a provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.

The 43a motor driver IBT-2 H-bridge module is an inexpensive, high power motor driver based on two BTS7960 chips

This driver 43a motor driver uses two high current half bridge Infineon BTS 7960 chip for motor drive applications. Interfacing to a microcontroller is made easy using this driver which features current sensing, slew rate adjustment and protection against over temperature, overvoltage, under voltage, Over current and short circuit.

This small size driver provides a cost optimized solution for protected high current PWM motor drives.

Features: –

  • 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board.
  • Voltage indication of motor driver output end; can solder heat sink.
  • Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2); isolation chip 5 V power supply (can share with MCU 5 V).
  • Able to reverse the motor forward, two PWM input frequency up to 25kHZ; two heat flow passing through an error signal output.
  • Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply; the supply voltage 5.5V to 27V.

BTS7960 IBT 2 43A H-Bridge Motor Driver Module Specifications: –

  • Input Voltage: 6 ~ 27Vdc.
  • Driver: Dual BTS7960 H Bridge Configuration.
  • Peak current: 43-Amp.
  • PWM capability of up to 25 kHz.
  • Control Input Level: 3.3~5V.
  • Control Mode: PWM or level
  • Working Duty Cycle: 0 ~100%.
  • Over-voltage Lock Out.
  • Under-voltage Shut Down.

BTS7960 IBT 2 43A H-Bridge Motor Driver Module Pin Description: –

  • RPWM: forward level or PWM signal input, active high.
  • LPWM: Reverse level or PWM signal input, active high.
  • R_EN: forward drive enable input, high-level enable, low level off.
  • L_EN: Reverse drive enable input, high-level enable, low level off.
  • R_IS: forward drive current alarm output.
  • L_IS: Reverse drive current alarm output.
  • VCC: +5 V power output, 5V power supply connection with the microcontroller.
  • GND: signal common low end
Datasheet: –

IBT2 datasheet

Package: –

1 x BTS7960 IBT 2 43A H-Bridge Motor Driver Module

Related Products at majju.pk

 

User Reviews

0.0 out of 5
0
0
0
0
0
Write a review

There are no reviews yet.

Be the first to review “BTS7960 IBT2 BTS7960 43A High Power Motor Driver Module”

Vendor Information

  • Store Name: sherjaan
  • Vendor: sherjaan
  • Address:
  • 5.00 5.00 rating from 3 reviews

You may also like…

BTS7960 IBT2 BTS7960 43A High Power Motor Driver Module
BTS7960 IBT2 BTS7960 43A High Power Motor Driver Module

 1,800.00  1,500.00

Majju PK
Logo
Reset Password
Shopping cart